System 2M DIY Kit

Part No. 011-0410

Water-Cooled Condensing Unit with Holdover Plate  Evaporator

Complete Parts List  (Included with Kit)

 

Item No. Part No. Qty

Description

1 010-1120 1 Mounting Kit for Danfoss Compressor
2 010-1180 1 Danfoss BD80F Compressor (mm)
3 010-1185 1 12/24v Power Module for BD80F
4 012-1005 1 Circle Water-Cooled Condenser
5 015-0280 1 SS Mounting Bracket for Danfoss Thermostat
6 015-0282 1 Danfoss Refrigerator Thermostat Service Pack
7 015-1510 1 200 - 150 psig Pressure Switch (High)
8 017-0032 1 30 amp/#10 Terminal Block - 6 pos, #8 Screw
9 017-0093 2 30 amp Terminal Block Jumper - #8 Screw
10 017-1002 1 40 amp DC Relay (SPST) - 12vdc
11 017-2011 1 10 amp Waterproof In-Line Fuse Holder
12 018-0101 1 Holdover Plate - 16" x 11" x 1 1/2"
13 020-0032 1 Sporlan Filter-Dryer - C-032
14 025-0031 1' Copper Tubing - 3/16" OD
15 025-0032 16' Copper Tubing - 1/4" OD
16 025-0033 16' Copper Tubing - 3/8" OD
17 025-0202 3 Copper Union - 3/8"
18 025-0422 2 Copper Long Radius Union Elbow - 3/8"
19 025-0502 1 Copper 45° Union Elbow - 3/8"
20 025-0601 1 Copper Street Elbow - 1/4"
21 025-0622 1 Copper Long Radius Street Elbow - 3/8"
22 025-0701 1 Copper Standard Tee - 1/4"
23 025-0702 1 Copper Standard Tee - 3/8"
24 027-0001 5 Heavy Duty Flare Nut - 1/4"
25 027-0002 2 Heavy Duty Flare Nut - 3/8"
26 027-0006 1 Reducing Flare Nut - 3/8" x 1/4"
27 027-0007 1 Reducing Flare Nut - 1/2" x 3/8"
28 055-0003 1 SS Mini Hose Clamp - 1/4" Band Width
29 055-0020 1 SS Mounting Bracket for Water-Cooled Condenser
30 055-0036 3' 3/8" ID x 3/8" Thick Tube Insulation
31 055-0105 1 SS Mounting Plate
32 070-0100 1 Shurflo Circulating Pump .5 pgm - 12vdc
33 070-0303 1 Shurflo Hose Barb Connector - Elbow 3/8"
34 070-0304 1 Shurflo Hose Barb Connector - Straight 3/8"
35 075-0200 1 Receiver - 2 lb x 1/4" flare
36 077-0150 1 Sight Glass SA12S - 1/4" Solder x 1/4" Solder
37 079-0661 1 Swaging Tool - 1/4"
38 079-0803 2 Stay-Brite #8 Solder - 3'
39 079-0806 1 Stay Clean Flux Paste - 4 oz Jar
40 079-2001 1 SS Tube/Fitting Brush - 1/4" OD
41 079-2002 1 SS Tube/Fitting Brush - 3/8" OD
42 079-2010 1 Abrasive Cleaning Pad - 6" L x 4" W
43 095-0000 1 TN2 Thermostatic Expansion Valve - R134a
44 095-0001 1 OX - Danfoss Orifice
45 096-0034 1 Schrader Valve Access Port - 1/4" OD Stem
46 096-0035 1 Schrader Valve Access Port - 3/8" OD Stem
47 096-0040 1 Base Valve - 1/4" Flare
48 096-0041 1 Base Valve - 3/8" Flare
49 211-0082 1' Tinned Primary Wire, Red - 18 AWG
50 211-0533 2' Tinned Primary Wire, Red - 12 AWG
51 211-0552 1' Tinned Primary Wire, Yellow - 12 AWG
52 240-0001 12' Safety Duplex Tinned Cable - 18/2
53 290-0001 6 Insulated Female Spade Electrical Terminal - 22-18 ga.
54 290-0011 4 Insulated Female Spade Electrical Terminal - 12-10 ga.
55 290-0102 4 Insulated #8 Ring Electrical Terminal - 22-18 ga.
56 290-0112 2 Insulated #8 Ring Electrical Terminal 16-14 ga.
57 290-0122 6 Insulated #8 Ring Electrical Terminal - 12-10 ga.
58 290-0212 3 Adhesive Lined Heat Shrink Butt Connector - 16-14 ga.
59 400-0010 2 Hex Head Mounting Bolt - 18-8 SS, 5/16-24 x 1/2"
60 400-0011 2 Flat Washer - 18-8 SS, 5/16"
61 400-0012 2 Lock Washer - 18-8 SS, 5/16"
62 400-0131 8 Nylock Nut - 18-8 SS, 8-32
63 400-0291 1 Hex Nut - 18-8 SS, 3/8-16
64 400-0322 6 Phillips Pan Head Machine Screw - 18-8 SS, 8-32 x 1/2"
65 400-0324 2 Phillips Pan Head Machine Screw - 18-8 SS, 8-32 x 1"
66 400-0451 1 Lock Washer - 18-8 SS, 3/8"
67 400-0901 1 Saddle Mount - #10
68 400-0911 15 Standard Cable Tie - 7 1/2"
69 NA 1 CD Manual

This list includes all of the components required to build your refrigeration system.  With basic soldering skills, your refrigeration unit can be ready to install in a few hours.

 

DIY Systems Kit Page